NEEBRC 3520 1850/2250KV Outrunner Brushless Motor AM32 Programming 80A ESC BEC for RC Crawler Car Axial Traxxas SCX10 TRX4 TRX6

Availability In Stock

This product is currently out of stock and unavailable.

Buy Now

Description

NEEBRC 3520 1850/2250KV Outrunner Brushless Motor AM32 Programming 80A ESC BEC for RC Crawler Car Axial Traxxas SCX10 TRX4 TRX6

ESC Description:
This ESC comes pre-installed with AM32 custom firmware. It is optimized for crawler vehicles, providing verysmooth and quiet operation of your crawler, but it is also suitable for various 1/8 scale or smaller cars. It features a built-in adjustable quad-group voltage BEC, with a maximum current of 10A, for high-torque servo applications. Additionally, the included e-Switch helps avoid failures caused by harsh environments. All wires are pre-soldered.

Motor Features:
CNC machined aluminum front and rear cover
14 pole high torque rotor offer stable output power
Small and light 3542 motor for your vehicle
1/8" shaft fits common RC pinions
Pre installed bullet connectors, 140mm silicon motor leads
Detachable design, convenient for cleaning and maintaining

ESC Features:
AM32 custom firmware
Sine wave start allows the motor to operate smoothly at ultra-low speeds
Variable driving frequency
Low voltage, runaway, and rotor lock protection
High-performance 32-bit MCU
E-switch, durable and waterproof

Specifications:
Name:
3520 Outrunner Brushless Motor
KV(RPM/Volt):1850KV 2250KV Optional
Stator: 14 pole 12 slot stator
Input Voltage: 2-3S LiPo
Shaft Length: 1/8" D shaft output (3.17mm)
Diameter: 35mm
Length: 41.8mm
Wire Length: 140mm (5.51in)
Connector: 4.0mm gold
Weight: 145g (1850KV), 149g (2250KV)
Mounting Pattern: 25mm for M3 screws
Suit For: 1/10 Scale RC Car

Name: AM32 80A ESC
Battery: 2~6S Lipo
Current: 80A (Continuous)
BEC: Max 10A, Output 5.2/6.0/7.4/8.2V, adjustable via DIP switch
Electronic switch supported
Fan: Included, with reserved power plug
Motor power connector: Not included
Wires: Power wire 14AWGx150mm, motor end 14AWGx100mm, signal wire 200mm, electronic switch 125mm
Dimensions:1/10 1/8
Weight:0.052kg

USB Link

For AM32/BL32, connects the ESC to a computer for configuration or firmware upgrade.
Portable and easy to use, simply connect the ESC signal plug, connect the USB Type-C cable to a computer, and install the VCP driver.
AM32 firmware is specifically designed for AT32 ARM processors, for controlling brushless motors (BLDC). The firmware is designed to be safe, fast, with a smooth and rapid start, and linear throttle. It is suitable for various vehicle types and flight controllers.

M32 features include:

● Firmware upgradeable via Betaflight pass-through, single-wire serial, or Arduino
● Servo PWM, Dshot (300,600) motor protocol support
● Bi-directional rotation
● KISS standard ESC telemetry
● Variable PWM frequency
● Sine start mode, designed to accelerate large motors

 

BEC Output Voltage Adjustment

Firmware Upgrade

Configuration Tool Download:

https://drive.google.com/file/d/1qw2f7nM6OZftIE5GTgMPWB5zXCELxYG9/view

CH340 Driver Download:

https://www.wch-ic.com/

1.Connect the ESC to the tuner, as shown in the diagram.Open the ESC Configuration Tool.

2.Check Direct Connect when using Arduino PC Link (do notcheck when using the flight controller interface).

3.Select your Arduino port.

4.Click the "Connect" button.

5.Read the ESC settings using the M1 button.Now, you can adjust settings, change tabs, upload new firmware, or load the default
eeprom settings.

6.After making adjustments, save your settings.To carefully check if your settings have been applied, close the connection, then reconnect and press M1 again.

7.

8.First,check the appropriate box. Second, select the serial port number where the tuner is located. Third, connect the motor to the ESC.

9.Choose and download the firmware needed for the direct upgrade.

Parameter

Pay special attention to a few points here:

1.If using a 6S lithium battery, do not set the sine power value to 10, as this will cause both the motor and the ESC to become very hot.

2.When using 3-4S lithium batteries, set the sine power value based on the direct weight of the vehicle, usually around 6-8 is appropriate.

Recommended Setting Parameters

For 3S-4S batteries, the recommended parameters are(set the motor KV value and the number of poles according to your motor’s specifications)

For 6S batteries, the recommended parameters are (set the motor KV value and the number of poles according to your motor’s specifications)

Warning:

1.If using a 6S lithium battery,do not set the sine power value to 10, as this will cause both the motor and the ESC to become very hot.

2.When using 3-4S lithium batteries, set the sine power value based on the direct weight of the vehicle, usually around 6-8 is appropriate.

Reviews

There are no reviews yet.

Be the first to review “NEEBRC 3520 1850/2250KV Outrunner Brushless Motor AM32 Programming 80A ESC BEC for RC Crawler Car Axial Traxxas SCX10 TRX4 TRX6”
Review now to get coupon!

Your email address will not be published. Required fields are marked *

Back to Top

Search For Products

Product has been added to your cart
0